Think Big.
We Engineer:
From early napkin architecture and high-speed PCB layouts to deterministic RTOS firmware, HIL automated testing, and volume SMT manufacturing.
0+
Delivered Systems
0%
First-Pass HIL Rate
< 0h
Architect Response
// Embedded India Turnkey Hardware Core
void init_embedded_system(void) {
power_rail_config(RAIL_3V3, ULTRA_LOW_NOISE);
uart_baud_init(115200, OVERSAMPLE_16);
lora_mesh_join(CHANNEL_915MHZ);
hil_fault_injection_guard();
start_freertos_scheduler();
}
// Status: Ready for Bring-upLive PCB Trace Width Estimator
Slide the current slider to instantly calculate IPC-2221 trace width geometry without leaving the homepage.
More than just service
We engineer enduring electronic product value through proactive design-for-manufacturing, silicon lifecycle sustainment, and dedicated hardware architecture.
Performance and Cost Optimization
Strategic component selection, alternative second-sourcing, and architectural power profiling, protecting your profit margins over the product's entire lifecycle.
Accelerated Time-to-Market
Turnkey prototyping, in-house SMT bring-up lab, and automated HIL verification compress development schedules from quarters to weeks. Start your new design experience with us.
Lifecycle Engineering
Post-launch firmware FOTA bootloaders, compliance test support (CE/FCC/BIS), and component obsolescence mitigation across 7+ year product lifespans.
Services we offer
From early architectural feasibility and rapid proof-of-concept prototypes to turnkey manufacturing support and high-speed firmware.
Full-Cycle Product Realization
Complete electronic product engineering: schematic capture, BOM optimization, thermal simulation, DFM reviews, and production handover.
Embedded Software & Firmware
Deterministic bare-metal and RTOS (FreeRTOS, Zephyr) drivers, HAL layers, low-power sleep management, and secure cryptographic bootloaders.
Hardware Design & High-Speed PCB
Multi-layer layouts (up to 16+ layers), HDI microvias, controlled impedance traces, differential skew matching, and EMC/EMI pre-compliance.
Board Support Package (BSP) Development
Custom U-Boot bootloader porting, Embedded Linux device trees, custom peripheral drivers (I2C, SPI, CAN, PCIe), and fail-safe FOTA updates.
IoT and Edge Computing Solutions
Connected sensors with LoRaWAN, Cellular (4G/LTE-M), BLE 5.3, Wi-Fi 6, and on-device TinyML machine learning for predictive vibration monitoring.
Automotive Embedded Systems
Automotive ECUs, CAN-FD / LIN buses, ISO 26262 functional safety compliance, and Hardware-in-the-Loop (HIL) automated test benches.
How we work with you
A transparent, milestone-driven process — from your first call to full IP handover. No lock-in, no surprises.
Discovery Call
Free 30-minute architecture review with our principal engineer. We discuss your product concept, operating environment, and feasibility — no commitment required.
Free · No CommitmentNDA + Proposal
We execute a mutual NDA before reviewing your schematics or IP. A detailed technical proposal with BOM estimates and milestone timeline follows within 24 business hours.
Within 24h · NDA-ProtectedDesign + Validation
Iterative hardware design sprints with regular review checkpoints. Automated HIL testing and DFM reviews are built into every milestone before board spin.
Transparent · IterativeIP Handover
You receive 100% ownership of all Gerber files, native CAD sources (Altium/KiCad), firmware repositories, BOM, and test reports. Zero vendor lock-in.
100% IP Ownership · Zero Lock-inInteractive Project Scope & Timeline Estimator
Select your project phase, silicon complexity, and regulatory targets for an instant turnaround forecast and milestone breakdown.
Standard MCU Architecture
- ✓Schematic Capture & Component Sourcing
- ✓Multi-Layer Controlled Impedance Layout
- ✓First-Pass SMT Prototypes (5 Assemblies)
1 Principal Hardware Architect • 1 Firmware Engineer • 1 DFM Specialist
Featured Engineering Case Studies
Production electronics deployed across Indian automotive, utilities, and consumer industries.
Automotive Bus AC Controller
Dual CAN-bus architecture, 12V/24V transient protection, and multi-zone PID temperature regulation for transit coaches.
Smart Water Dispenser Controller
Capacitive touch interface, optical water level monitoring, RS-485 telemetry, and automated sanitary UV cycles.
Substation RTU Edge Gateway
Linux BSP with dual Ethernet, galvanic isolation, IEC 60870-5-104 protocol support, and fail-safe dual bank eMMC FOTA.
Latest Technical Articles
Peer-reviewed hardware guides, functional safety breakdowns, and firmware architectural patterns.
Engineering partnerships, in their words
What technology leaders and engineering directors say about partnering with Embedded India.
Worked with our team? Share your engineering experience below.
Frequently Asked Questions
Everything you need to know about our turnkey hardware, firmware, and manufacturing contracts.
What is the typical prototype turnaround timeline? +
Standard turnkey prototype turn is 3 to 4 weeks, which includes schematic design, layout routing, bare PCB fabrication, component sourcing, SMT assembly, and bench verification bring-up.
Who retains the Intellectual Property (IP) and design files? +
You retain 100% ownership of all IP, Gerber manufacturing packages, BOMs, native CAD schematics (Altium/KiCad), and firmware source code repositories upon completion.
Can you assist with volume production and SMT manufacturing? +
Yes. We partner with ISO 9001 and IATF 16949 certified EMS facilities across Bangalore, Pune, and Noida for pilot runs and high-volume production with custom automated factory test jigs.
Do you sign NDAs before reviewing our schematics or design files? +
Yes, absolutely. We execute a mutual Non-Disclosure Agreement (NDA) before any confidential design data, schematics, or IP is shared. This is standard practice on all engagements from the first technical review onward.
What happens if the first PCB board spin has an error? +
Our rigorous DFM review and automated HIL verification process is designed to catch errors before any board is fabricated. In the rare event that a design issue requires a board re-spin, we include one revision cycle at no additional layout charge within the original project scope.
Can you work with our existing Altium Designer or KiCad project files? +
Yes. We work natively in both Altium Designer and KiCad. We can continue an existing partially-completed schematic or layout, or perform a full re-architecture review starting from your existing project files. All deliverables are returned in your preferred CAD format.
Is there a minimum order quantity for prototype manufacturing? +
No minimum order quantity for prototypes. Our standard turnkey prototype package includes 5 SMT-assembled boards, which is sufficient for bring-up, functional testing, and regulatory pre-compliance measurements. Single-unit handbuilt prototypes are also possible for urgent feasibility validation.
Ready to engineer your next embedded system?
Speak directly with an Embedded India systems architect to evaluate your technical requirements and timeline.